Search results

Here is my 2007 series 1 VE SSV, It has had quite a few mods done on it over time. Here are the specs: - LSA Longblock (old motor torched a piston) - CAPA supercharger kit - Crow cams camshaft and valve train - Full 3" stainless manta - Allfast built 4l80e (good for 1000 hp) - Allfast built...

Hello, I was wondering what is required to convert a 2007 series 1 (my6) ve ssv to flex fuel? I have heard from a few friends that the ecu in my car isn't setup for flex fuel (is that true)? Thanks!

Hello, After prolonging this as much as possible, which resulted in a 360 at a roundabout in the wet, I need a new set of tires. Looking for a decent set for around $350 per tire, my car has staggered rims (20 x 8.5 front, 20 x 10 rear) can provide more information if needed Thanks!

Hello, I am currently looking for a twin plate clutch to go in my 2007 ve ssv as my current single plate one is slipping at my current hp. this car will still be a DD so I don't want the clutch to be jerky when engaging (have driven a mates car that has a twin plate ceramic clutch that takes...

Hello, can anyone recommend me a good engine builder in the perth area? looking to get an engine built and hit a road block trying to find a good shop. Thanks!

I managed to score a set of hoosier DR2 275/40r17 drag radials. I started looking for rims to fit them and got told that I would need to roll my fenders to fit them. Is this true? What offset rim do I need to not require me to roll my fenders? Am i required to roll my fenders to fit any brand...

Hi, I was wondering if anyone knows where to get a banjo bolt copper crush washer for the rear calipers on a ve ss.

Hi, I was looking at getting a set of 18" rims to use for drag racing. My car has had a CTSV v2 brembo conversion (6 piston front, 4 piston rear) and I don't know any 18" rims that will fit that won't cost me a kidney. Anyone got any recommendations for reasonably priced 18" rims(either 245 or...

Hi, I was wondering if the E1 HSV pod cluster (the one above the radio) was compatible with a series 1 ve ssv. I was wondering as my current one is starting to show signs of sun damage and I like the look of it vs the stock gauge cluster. Does anyone know of any series 1 ssv's that have had it...

UPDATED IN NEW POST

I was wondering what would be the best brake upgrade for a series 1 ve ssv that doesn't require me to sell a kidney. I have read on here that the dba t3 4000 club spec seem to be an ok option for rotors, what would be the best caliper to go with it? if any. My current rims are 20"

I was wondering if a LS3 is a straight "plug and play" swap in a series 1 ve ssv. I have heard that it is but I would like to get confirmation.

Hi, I was wondering what the max width of tire I can put on the rear of a 2007 ve ssv sedan without modification. I am currently looking at getting a set of drag radials for my car and can't find any that match the width of my current ones (245). I hope to finally get an answer to my searches.

I was wondering if the E1 clubsport bumper is a straight bolt on for a ve ssv series 1? Also does the E2 and E3 front bumpers require modification to fit?

I have recently got a cam put in my car. When I went to pick it up, the tuning shop said they also cleaned the throttle body as it was full of carbon. Everything was fine until I noticed a strange issue with the car now suddenly reving up to 1.5-2k rpm when I push the clutch and brake in while...

Hi, I am looking at getting an aftermarket head unit for my 2007 ve SSV series 1 to replace my aging radio. I have about 1.5-2k to spend and my location is Perth. I would like one that has reverse camera, gps and android auto. Thank you for reading

(Updated Post here)

Hi, I am looking for suggestions on what extractors and cats I should go with (currently have a 3" stainless steel manta cat back and I am planning to cam and supercharge later on) My budget is about 1.5k (can go slightly higher if needed). I am located in Perth and my car is a 2007 Holden...

Which model of gear box comes stock from the factory in a 2006 ve ssv sedan manual? When I try and google the question, it comes up with 3 different answers, (t56, t56 magnum or tr6060). Thank you.

I am looking for a full stainless steel exhaust system for around 1.8k give or take $100 (Can go slightly higher if needed). I do plan to put a CAM in later on and possibly supercharge it. I am located in Perth WA and I would prefer to support Australian manufactures if possible. My car is a...