Search results

Hello, I want to install AC on my VK which has an LS1. I purchased castlemaine rod shop AC bracket and compressor. https://www.rodshop.com.au/high-mount-air-conditioning-ls1-ls2-ls3-engines This Kit Uses the Sanden 508 Type Compressor Now i need to purchase the condenser and receiver drier...

Passenger front door on vs statesman won't open. on the inside the door lock won't go up when remote is pressed or when manually pushed up. Stuck in lock position. Door won't open from inside or out no matter what. The Big issue can't take off door trim due to the screws that hold it in are...

Hi all Need help how many hsv vs statesmen were made. I recently purchased one and want to know how many made. the number on the hsv tag does it represent the number made for that model or the total amount of vs hsv's made.

Hello, i have ls1 in my VK, went for a drive last night and the car has developed a miss under light acceleration, then under hard acceleration the engine work fine, need help, any ideas?? thanks its, like a switch miss and then off, no inbetween.

Hello, Hope someone can help. I have a VR V8 engine wiring loom for VR. What is the difference between VR and VS wiring loom? Thanks

Does anyone have a Damper Fuel for a 304? Thanks Or what can i use as a replacement?

Hello, I have a 4L60e for my 304. The speed sensor is on the passenger side, however my wiring loom is for a driver side speed sensor. My question, What year model user's passenger side speed sensor and when did Holden change to drivers side speed sensor? Also What can i do to fix my problem...

Hi all, I need to rebuild the bottom end for a 304 VS engine, need to replace the crank bearing, conrod bearing and pistons rings. I don't have all the tools to a. measure the clearances. b. Piston ring compressor c. Bore honing tool. d. Other. Also I don’t know tolerances. Hoping someone...

Hello, I am doing a VS V8 conversion from V6 to 304. I have installed the engine in the car with the wiring. When to start the car - no fuel pressure. I removed the lines to check fuel, and no petrol was pumping. Any ideas?? Does the ECU control the fuel pump?? Fuel pump was working with the...

Hello, Trying to work out the engine wiring loom for my V8 304. I am change from v6 to v8. I have a 304 wiring engine loom. Need to know what the below is for. Can someone please help? 6 pin straight female, please refer to photo, is next to ignition module plug

Hello, Does any have the measurements for the dayglo orange for a VK Big Banger? Need to know where the V starts in the center of the bonnet and top of the roof. Thanks Muzza

Hello, Installed head lights. however i don't have parker lights working. The below wiring is for the blinker and low and high beam globes.I got the blinker, low and high beam to work. The headlight globe has 3 pins low, high beam and earth. Please note: The car had no lights when purchased so i...

Hello, Installed head lights. however i don't have parker lights working. The below wiring is for the blinker and low and high beam globes.I got the blinker, low and high beam to work. The headlight globe has 3 pins low, high beam and earth. Please note: The car had no lights when purchased so...

Hello, I have a LS1 in a VK - Does anyone know which OTR fits the VK engine bay with standard bonnet? I have an VK aluminium radiator with aluminium fan tray. Does an LS1 od LS2 or LS3 fit?? Thanks

hello, I just installed a LS1 into my VK. This has been a one year project. When to start the engine, engine will not start. Last year i had the ECU re mapped by a guy in North NSW. I checked why the engine will not start - don't have spark at the plugs, there is power at the coil packs however...

I purchased an LS1 second hand cam. need to know is it a stock cam, can tell me? Refer to specs off the front of the cam

Hello, I purchased a second hand cam. Want to know if it is a stock cam. Can anyone help? refer to photo of cam.