Search results

*~~Bump~~*

*~~Bump~~*

ITEM: A lower bracket for a SC14 supercharger to bolt on to a VN VP VR V6 commodore, High grade metal, Laser cut and never been fitted to a car. These Brackets are on order so PM me if you would like one. LOCATION: Mildura, VIC CONDITION: New PRICE: $45 Pickup Or $55 Posted PAYMENT...

sure do mate

got 139.5db at 55hz we did a sweep from 70hz to 55hz and it peaked at 55hz so who knows it could have more in it

Mazda 121 (daily) T2 15 Rockford fosgate 1000rms 1500bd Rockford fosgate Amp 75rms Rockford Fosgate 6.5s Parcel shelf Clarion Splits front **** Sony headdeck 3cube Box tuned at 60hz 6"h L port It was fired forward it got 139.1db Today is the sound comp its rear facing now hopefully...

Dont laugh to hard its only a slap up job haha

Today is the day, i was going to make a Octaport box but didnt have enough time so i will just make do with what i have at the moment. I turned the box around and faced it to the back it does sound like its louder but i am not sure how much it will be. hopefully i crack the 140s thats all i am...

Hey guys I have a slap up system in a Mazda 121 bubble and entering it in a SPL comp this saturday Specs T2 Rockford fosgate 15inch in 3cube box 6inch vented tuned to 60hz Made 139.1DB facing forward but i took it home and faced the box firing back and it sounds heaps louder But if it will...

sold remove thread.

ITEM: Yella Terra 1.7 Ratio VN VP VR V6 LOCATION: VIC CONDITION: Used (hardly) PRICE: $300ono DELIVERY/PICK UP INFORMATION: PAYMENT OPTIONS: COD, Direct Deposit, CONTACT: PM,

Thanx for the advice it will help out alot. The paint was a quick spray can job years back haha. No doubt the engine bay is probably the hardest thing on the car to paint. I also have some holes that have been welded up but i need to grind back the metal some more so its flat how would i get...

Ok guys i know its been a long time and proberbly forgotten but i am starting the prep work on the engine bay so i can put the motor back in. As you can see from the picture the paint is shocking and most of the black came off with the gernie, how should i go about prepping the engine bay...

I have got off my arse for a change and did some on the VN the last couple of days. The parts i have fitted to the car 3.08: LSD diff With Whiteline Adjustable Panhard bar. What i noticed when hooking up the brake lines from the VS LSD Diff to the T piece on the car they where a different...

That sucks dude...

Are they on the block?, if they are loosen one side off abit lower it in and then tighten it back up, or take it off and put it back on when its in the car. Just keep having a play it will get on there, make sure you dont use anything to push on the thread and strip it or it will be harder...

inboxed....

Yeah i found his thread on the upgrade, i will make up the brackets myself and fit the VT booster/master, then all i need is the Hub Adapters to fit the Calipers and Rotors. Is there any upgrade for the rear? is there anyway the VT Rear will fit or no chance being IRS. Or do i just get some...

The Huds listed on ebay are the same as what i am looking at, i will measure the spline on the VN and get them to measure the diamiter of the wheel hubs and go from there. What's a VT booster and master cylinder worth these days, thanx for the help guys

I have a VT brake upgrade for my VN Commodore its not a full kit as i am after the Hub adapters. I went to a bearing place that make them for trailers and so fourth i was wondering if the spline on the VN is the same size as the spline on a trailer and if they will fit i think there 40mm but...

ITEM: Hey guys, I am seeing how much interest i will get in making some more SC14 Brackets up to mount on VN VP VR V6 commodores. This is the Bottom Bracket that bolts to the head and bottom of the Supercharger to align the pulleys. It is professionally made with a Laser cutter and is top...

ITEM: Genuine VN SS side skirts, in good condition have no need for them. I also have a SV5000 Rear Wing as well. PM me because i dont always check the listing LOCATION: Vic Mildura CONDITION: used PRICE:$80 DELIVERY/PICK UP INFORMATION: Pickup or postage. PAYMENT OPTIONS: COD...

Powerslave i think it is from this site, had a Wade 992a Cam with Headwork and he got 140rwkw

are the heads ported and polished, you should be around the 135-145rwkw mark.

Well had a late night doing home renos and found myself in the shed taking parts off the car to pull to motor out and replace the rear main seal. I also notice alot of my exhaust gaskets have been leaking also and a bolt wasnt even on the bottom of the turbo housing so now i will be tripple...

Still for sale.

Sure mate, PM me your address and i'll get a quote.

Bolt ons, Cam, Head work port polish, get the heads shaved as well up the compression.

Yeah i was going to do that just wasnt 100% cheers mate.

ITEM:Genuine Plastic VN SS side skirts, in good condition LOCATION: Mildura, Vic CONDITION:Used PRICE: $100 DELIVERY/PICK UP INFORMATION:Pick up Mildura, But will post PAYMENT OPTIONS: COD, Direct Deposit, Funds Transfer CONTACT DETAILS: Private Msg

Update, Drove the car for the first time in 8 months today when i moved it to my new house, i noticed it was leaking a lot of oil in the drive way, i have a look to see where it came from and it looks like its between the bell housing and its not Gearbox oil :( So I will be pulling the...

Willing to sell the 3.9 Mini spooled center for the right price. inbox me

i was thinking 80-100

should be worth more than that surely.

ok cheers, So the other Question what do you think it would be worth? It has a small tear on the top, but apart from that it is in good condition and has the boss kit.

its got 06-90 on possibley off a sv90?

Yeah i am not sure i am asking the guy if there is a serial number or something? there should be one shouldnt there?

The only info i have on it is its a HDT Momo steering wheel..

Hey guys, Just wondering what this steering wheel is off? and whats it worth in the condition its in and does it look authentic thanx

ITEM:Holden Commodore Diff, 3.9 Gears, Bearings replaced, Minispool Good for Drags. Its in a VN commodore, It will fit VN VP VR VS solid Diffs. Hasnt had much use. LOCATION: VIC CONDITION: Used PRICE: $400 DELIVERY/PICK UP INFORMATION: Pick up or Freight. PAYMENT OPTIONS: COD...