flywheel

G'day. Bought the manual ute brand new October 2008. Within 6 months the clutch was slipping. Holden replaced the whole clutch assembly from pedal to flywheel including cylinders lines and thrust bearing flywheel pressure and clutch plates. Just now pulled the motor out to "freshen It up" and...

Hi guys, had a dragging clutch so have pulled apart clutch assembly to replace necessary components, just need help identifying what flywheel I have as I know you can't reuse the dual-mass ones if they're too far gone. 2007 VE sv6 manual (aisin ay6), 330000km. Due to the Ks of the car I don't...

Hey I'm converting my 99 vs ute from getrag to t5, I got an 8 bolt flywheel from the wreckerz along with everything else I'd need to convert the gearbox successfully. I removed the getrag along with the cluth and dm flywheel only to find two locating dowels, the 8 bolt flywheel i have doesn't...

I have a ve sv6 with 6spd aysin gearbox at idle with the clutch out there is an audible rattle when the clutch is pushed in it stops. Also in first and second under 1800rpm it makes a rattle then too most noticeable when going around a round about or taking off from the traffic lights. At first...

So ive been looking around for a new engine for my car and i have to match up the engine codes,but ive been told that i can use the (Auto) 10H7A engine, but do i just have to change the flywheel to a manual one or do i need to get the engine tuned aswell my engine code is 10H7B (manual) cheers

G'day all. Converting my 95 vs exec to manual. bought a getrag manual box with all wiring, hydraulics, computer, shaft etc but the wrecker mentioned that because it was out of a later model (apparently it came out of a VS cop car??) that the flywheel is different and i'd be better off with a...

Hey guys, just after some ideas/thoughts. Ive got a VY SS M6, on the way home from work this arvo i heard a snapping sort of sound then the gear disengaged & i couldn't get it back into gear, none would work. The clutch was springy & would push down to the floor. Although when i turned the...

So I bought one on trademe but it was too small for my clutch pressure plate, so I'm assuming it is not an rb30 flywheel. Would anyone have any idea what type of rb flywheel it is? Just less diameter than it should be. Also I now need to buy a new flywheel, how can I be sure it is a rb30...

i am currently in the process of doing Auto to Manual conversion. And Ive done some reading about the solid mass flywheels and i heard they make some sort of rattle is that all the time or just when u frist take off and how loud would it be ? or should i just put the dual mass flywheel back...

Ok, today i tried to install a new gearbox and clutch in my vk with a 6cyl black motor, previously it has a mc6 phillipino box and i want to put in a M76 borgwarner box. Everything went smoothly until i tried to adjust the clutch only to find that i couldn't, it would adjust all the way out and...

Lost my manual somewhere and i need to know what your supposed to tension the flywheel bolts and clutch bolts down to. Car is a vk 85 EST black motor. Thanks

Please Help,Doing manual conversion and i used the auto flexplate bolts on manual fly G'day, is it possible to use the Auto flexplate bolts into the manual flywheel, i put locktite on them all and they spun it a bit before they were finger tight then a turn or so with the torque wrench before...

Hopefully someone can help me out im chasing a Manual Flywheel cover for a V6 VP Commodore, doin a conversion and thats all i need before i can put it back on the ground and go cruising. Email if you have one or know where i can get one, im ringing the wreckers tommorow but dont let that stop ya...

Hopefully someone can help me out im chasing a Manual Flywheel cover for a V6 VP Commodore, doin a conversion and thats all i need before i can put it back on the ground and go cruising. Email if you have one or know where i can get one, im ringing the wreckers tommorow but dont let that stop ya...

Hey guys, I've been trying to do as much research as I can by searching and not asking too much questions, but as I'm planning on doing my manual conversion around New Years and trying to avoid spending as much money as possible in order to get the bulk of the work done when the car won't be...

please delete sold sold sold please delete ITEM:VN Series 2 - VR 8 Bolt V6 Flywheel LOCATION: Nsw , Coffs Harbour Area CONDITION: Used good condition, has heat marks as any flwheel would, the face has no gouges or wears in it, if you r installing it and putting in a new clutch you...

myself and a mate (mischa) we have both been doing manual conversions in the past few weeks and i have also noticed a lot of interest on the subject here so for all that are not sure here is the list of parts you need for a VN-VR V6 Manual Conversion. Manual Gearbox Manual Tail shaft (can be...