pressure

Hey I need some help. I just recently rebuilt the bottom end in my LS1 VY Berlina. Since the rebuild my check oil warning keeps beeping at me. First I thought it was the oil pressure switch. I replaced it, no change. Then I thought perhaps too much oil, that seemed to help it but now my problem...

My 2013 VE SV6 LFX, has just decided to have a fuel issue one day any not start again. I've replaced both the electronic and high pressure fuel pumps. So on prime I get 60 to 65 psi and the beginning of crank it rolls up to 1800psi, hits 1800 and then dies off to 30 psi and I cannot figure out why

Hi lads, I finally got around to replacing the lifters, bolting the heads back on etc. I still get quite a loud tapping (see video I had it running for 10mins thinking it might go away). I think it's louder than before but same sorta sound. Noted: -Oil pressure stayed at 30psi on idle even...

Hi, I think I posted this originally in the wrong section... I have a VX SS series 2 and planning to install an oil pressure gauge. For those that have done this with the same setup (2002 ls1) – which way did you do it? I was going to buy an adapter plate for just above the oil filter...

Hi, I have a VX SS series 2 and planning to install an oil pressure gauge. For those that have done this with the same setup (2002 ls1) – which way did you do it? I was going to buy an adapter plate for just above the oil filter housing where I will plug in a new sensor but wondering if it is...

Hi Commodore Lovers, My VZ Failtec is getting the dreaded "check engine" error, my mates checker says it's the oil pressure sensor, now I'm getting intermittent "check oil" warnings even though oil level is good and no leaks, not running like a tractor, etc. (Don't worry I've been thru the...

Hi All. Couldn't seem to find an existing thread and I don't see it in the manual. Are the numbers written on these oil pressure gauges arbitrary or do the mean something? 1 - 3 - 5 Bar perhaps? Thanks

Hi, the vehicle in question is a 2002 holden commodore vx v6 with 201000 on the clock. My main issue is when the fuel cap is screwed in to place the fuel tank immediately starts to suction in. This is easily visible by looking underneath at the tank and seeing the tank rise off its brackets...

I own a VR Exec S2 Wagon. I had a secondhand auto trans installed beginning of last year, no recon, I've been having problems recently with it, it struggles to change from 1st to 2nd, but gets better when warmed up, the speed sensor display has stopped working and the lights on the trans...

Hi guys, Recently I noticed my stock 3.8 auto had been absolutely guzzling the fuel. I checked the trip computer, and it was giving an average consumption of 21l/100km which is ridiculous, considering I never rev it over 3000rpm. After a couple days of grandpa driving, it went down to...

hi guys just got an auto-meter ultra lite electric oil pressure gauge and just want to know how you guys have installed the sender as i dont have enough room to put it where the original one is as its too long and hits the alternator? any particular adapters i can use or just a matter of getting...

So I have a completely custom build (FC Holden) and running VS calipers all round and was given a VT brake booster and brake lines. What implications can I expect with this setup? Cheers

Hi Guyz, I'm looking for VZ A/C Performance table similar to the one I attached below. This table in the attachment below is extracted from the service information manual for Chevrolet Lumina 2007 which I believe is also known as Holden Commodore VE. According to my information after...

Hi Guyz, I'm looking for a VZ A/C Performance table similar to the one I'm attaching below. This table in the attachment, is extracted from the "Chevrolet Lumina Model Year 2007 Service Information manual" which I believe is also known as Holden Commodore VE. According to my information VZ...

hey all, i have a question, is it possible to put a light in behind the dial of a pressure gauge ( that doesnt have a light hole ) so it can be visible at night? i have a pressure gauge that i want to put in my car for my airbag tank, i was wondering if i could drill a hole in the back of...

Hi Guys, I have a track day next week (wooo) in my Monaro CV8 Series III. I run Pirelli Dragon's 235/40z R18's and wondering what you would recommend a good tire pressure to start with would be. I understand that tire pressure will need adjusting on the day for best performance, but wondering...

Hey guys, I picked up my '04 VY Series II S Commodore, last year around september, and this little device came with it. I have no idea how to work it, or what model it is, considering there is no model number and i never received a manual either. So anyone have an idea how to work...

Does anyone know what kind of pressure a stock standard Vk V8 radiator will take? stock is 105kpa. Is it possible it can take 135kpa or will it blow or eventually blow?

Hey guys, Just wondering if anyone has done this? Is there somewhere convenient to fit the sender? Like a T piece or is there a sandwich plate available to take a sender between the block and filter or something? This is for a VT series 1 V6 btw. Thanks all.