Search results

I have 2 replacement pcv valves for an ls1. part number pcv-001. 1 is brand new , the other was on the car. both are leaking air if i blow through them like a controlled leak. the old genuine one i have is airtight sometimes. Is pcv-001 the correct part for an ls1? is it supposed to have a...

i have an l67 conversion ive been working on. Ive been logging data, just idling in the driveway because I've got a bit of a misfire. it does this thing where the engine starts to get a bit warm (even if it goes over 100deg). the fans wont kick in so i turn the car off and back on for the fans...

Hi guys, I've been trying to order some pistons for my front calipers (for my vx) and I seem to be a bit confused, I believe the part number is K272-020 (Diameter: 42mm / Height: 43.7mm), I've been supplied with part number K272-040(Diameter: 41.9mm / Height: 44.5mm) which I think is to suit BA...

Hi all, just diagnosing a vacuum leak on a vx ls1. I was having a look at the charcoal cannister and i was wondering if anyone knows if youre supposed to be able to blow air into the vent valve? Or is my valve stuck open? Does anyone know the way to test the vent valve? is there even a valve...

Replaced the factory cam with a new one. Cam is a factory replacement. Will i need to get a tune? Or should it be exactly the same? currently running rich with a factory tune. trying to diagnose.

Hi guys, just a quick question. Do the bolts used to bolt down the supercharger on an l67 need to be threadsealed? I can't remember if the threads are exposed on the inside of the LIM. Cheers

Hi guys. Have vs l67 manual wagon Ive been putting together. I'm having problems working out the VSS input. I'm currently running an l67 ecu from a vs statesman but obviously being from an auto, the ecu isn't getting a vss signal. My Speedo on my dash works fine, Ive just got the stalling...

Hi guys, I picked up a Whiteline sway bar for my vs and I noticed that they come with specific link pins (in the kit)when new. Does anyone know where I'd be able to grab a set? Or what the part number is? Surely I dont need to buy another sway bar to get the link pins...

Ok so I've just had my l67 fully reconditioned. New everything. Old mate said the cam bearings were ok so they were not replaced. So new pistons, rings, pump, and bearings. Also crank needed a regrind, and cam was shot. So new cam also. It's all been done and out back together. When I start it...

Hi guys, just working on an l67 rebuild at the moment and I'm trying to chase down some shorter pushrods. I've sized them up at 6.95" but it seems that the only ones I can find at that size have a larger radius and wall thickness. Has anybody run thicker pushrods in the l67? Do they fit?? If...

Hey guys, I've bought myself a rebuilt l67 and dropped it in my wagon. It's been sitting for a while prior to being installed. First time I ran it, I thoroughly primed it before starting. I started it and got it up to temp. It sounded alright then after a bit it started to sound horrific. Alarm...

I've just noticed that the part numbers for vs ute and wagon exhaust are different. Aren't they supposed to be the same?? Str118 for redback wagon Str110 for redback ute Both come with the same tail pipe though.

Hey guys I'm. Doing an l67 conversion and I have a rogue green wire on the firewall, drivers side. Does anyone know where it goes or what it's for? Cheers

hi guys,im doing a manual conversion on my l67 atm and im trying to get the flywheel mirror balanced but i dont have the original auto flex plate from the motor. it didnt come with it. What is going do be my best option? will any l67 flex plate work? or am i going to have to pull out the crank...

Hi all, I'm about to swap out a noisy thrust bearing, and I remember someone telling me to use a Falcon thrust bearing because they're a little bit stronger? Has anybody heard of or done this? Cheers

Hey guys, i converted my vx to ls1 so i have an ecotec with wiring, ecu and everything i pulled out during the conversion. i know people have done the conversion using a vs ecotec and modifying the buick loom, but since i have access to a wiring loom and ecu, is it possible using the vx loom...

Hey guys, converted my vx wagon to ls1. I'm just wondering if anyone knows which way the fuel filter goes? Pretty stupid question but I've never had anything to go by.Anyone able to help us out?

My vp has a shagged motor in it, and i have a spare ecotec in my garage from when i converted my vx to an ls1. So i have everything that came off my vx. ive seen that the conversion can be done using the vp ecu and wiring, but as i have access to the ecu and wiring from my vx, i thought it will...

Gday guys. my ls1 was running a bit rough, so ive been trying to fix it and get it running nice again but i cant seem to work out what the issue is. It hasnt been running the best and last week it actually started having a solid miss at idol when it was up to temp. It also surges under...

Hey guys, i thought id start a new thread for her, the old one got cluttered with stuff from my old wagon..etcetc. anyway here goes. Name: Jacob Model: Berlina Wagon Colour: Blue Bodykit: None Engine Type: Gen III 5.7 Engine Mods: Had an OTR but took it off Power: Never enough Exhaust...

Hey guys. Ive been having some alternator issues. When I indicate and whatnot, all the dash lights dim with the indicator. So I thought id have a problem with the battery or alternator. The battery tested out fine, and after havibg the stereo going for a couple hours at the drive ins last...

hey guys. just swapped the battery loom over and i noticed this plug is different.. what is it? and how would i get it to work?

are they the same?? ive got v8 ones but my ones that came off a v6 are almost new

Hey guys. im in the middle of doing an ls1 conversion on my v6 vx berlina. And i was wonedring if the fuel lines need to be changed over? Or am i able to use the v6 lines? ive had a look and it looks like a massive headache with all the brake lines and whatnot. if it is necessary, what would...

Hey guys just in the middle of my ls1 conversion and I was wondering if I was able to use my existing fuses and relays under the bonnet or do I have to swap them?

Gday guys. Just doing a gen3 conversion abducted I cant work out how to remove the steel fuell lines. Anybody know how?

DESCRIPTION: Wanted to buy ITEM: V6 t5 gearbox and a heavy duty clutch LOCATION: Melbourne CONDITION: Preferebly good DELIVERY/PICK UP INFORMATION: will pick up or will organise freight if its worth it. PAYMENT OPTIONS: cash on pickup CONTACT DETAILS: post, inbox OTHER INFO:

gday guys, just wanted to know will ineed an engineers certificate for my vp if i put an l67 in it?

just got the car running. im having a problem when changing gear. every now and then, it grinds for a second as its going into gear, even with the clutch fully in. the clutch cable is fully tightened so im not sure if the gearbox is stuffed or if its just the clutch cable. any ideas?

Hey guys, I just did a manual conversion, but I don't have the clutch inspection plate, i know it will drive without it but will I ruin something driving without it? If So, does anyone have one they want to sell?

i converted my vp to manual, just wanted to know, as ive had to bridge the park/neutral and the engine light is on all the time. is the ecu still working as it should?

hey guys. doin a manual conversion and my rear seal was leaking a bit, so i pulled it out and grabbed a new one, and i read that if it goes in too far that it blocks an oil gallery or something? my question is, whats the best way to put the seal in?

gday guys, does anybody know how to tell the difference between a normal clutch and a heavy duty clutch by physically looking at it? i got a manual conversion the other day and the guy said it was a heavy duty clutch but i cant tell it from a regular one...can anybody explain how i could tell?

Hey guys, I'm chasing some 225 wide tires for my ceptors... I was wondering if anyone had any recommendations on what would be the best grip/price combo to go with. Also where would be the best place to get them?

gday i need to press out a couple bushes and im about to make myself a tool. What kind of piping do i need to use? and where can i get it?

Hey guys.. I put a minispool in my vp and I'm having a problem I think... When I turn right, it skips so bad that the whole car shudders.. But when I turn left, it skips a little, but hardly at all.. Both back tires are the same... Have I done something wrong?

Gday guys.. I had 2 Diffs That were both for a vp wagon.. Both are the same ratio... But the gears themselves are slightly different.. Why would they be different? And what would the difference be?

DESCRIPTION: Wanted to buy ITEM: 2 x 15x7" stockies...preferably with tires but not essential LOCATION: Vic CONDITION: new or used DELIVERY/PICK UP INFORMATION: will comme pick them up if in the area or will organise freight if need be.. PAYMENT OPTIONS: will pay in cash...

gday guys...gonna pick up some 7inch interceptors with 255 wide tires on them...my question is, will they be ok for the front of a vp? or will they be too wide? i dont want to put them on the back as i burn thru rears.

Gday guys.. Just installed a minispool in my diff and when im doin about 50km and up..when im just rolling, I get like a loud bearing noise..but if I'm accelerating..it doesn't make noise.. Did I mess something up?